<?xml version="1.0" encoding="UTF-8"?><!-- generator="WordPress/2.9" -->
<rss version="0.92">
<channel>
	<title>SRO Magazine</title>
	<link>http://articles.sromagazine.com</link>
	<description>SRO Magazine</description>
	<lastBuildDate>Wed, 27 Jan 2010 01:04:42 +0000</lastBuildDate>
	<docs>http://backend.userland.com/rss092</docs>
	<language>en</language>
	
	<item>
		<title>Aftermarket Front Bumper Installation on a Honda del Sol</title>
		<description><![CDATA[Materials/Tools:
- Philips screwdriver
- Drill with ¼” drill bit
- 10mm wrench
- Flathead screwdriver (optional)
Step 1:
Pop the hood and remove all the screws shown in the below picture with a Philips screwdriver.

Step 2:
Turn the wheel inwards so it’s out of the way. Pry the inner lining of the wheel well out and away from the front bumper [...]]]></description>
		<link>http://articles.sromagazine.com/aftermarket-front-bumper-installation-on-a-honda-del-sol/</link>
			</item>
	<item>
		<title>Break down of a car remodel</title>
		<description><![CDATA[Break-down of a car remodel
When first starting a project car , there are three main categories to split the remodel.
Exterior: Would have to do with any new body parts such as body kits, wings, fenders, etc. Also paint and any other repairs to the outside of the car.
Interior: All interior work , carpets, seats, stereo [...]]]></description>
		<link>http://articles.sromagazine.com/break-down-of-a-car-remodel/</link>
			</item>
	<item>
		<title>How to Install a Injen Cold Air Intake on a 2005-2006 Scion TC</title>
		<description><![CDATA[Tools: 10mm Socket Wrench, Flat head screw driver

Remove the battery tray from the engine compartment prior to starting this installation.

Remore the mass air flow sensor (MAFS) from the stock air intake box and set it aside for further instructions.

Loosen the clamp at the throttle body and disconnect the air intake box from the resonator duct [...]]]></description>
		<link>http://articles.sromagazine.com/how-to-install-a-injen-cold-air-intake-on-a-2005-2006-scion-tc/</link>
			</item>
	<item>
		<title>Installing PlasmaGlow Neon License Plate for the Scion xD</title>
		<description><![CDATA[Tools Needed:
-Electrician Tape
-Wire Strippers
Steps:

- After getting your new PlasmaGlow® neon license plate out of the casing, proceed to open the hatch (trunk) of the car.

-BUT, first always make sure you’ve unplugged your battery before performing electrical work on your car.

- There&#8217;s 2 large compartments that will give you access to the license plate lights (already [...]]]></description>
		<link>http://articles.sromagazine.com/installing-plasmaglow-neon-license-plate-for-the-scion-xd/</link>
			</item>
	<item>
		<title>Grudgefest at Sacramento Raceway</title>
		<description><![CDATA[On Saturday October 17, the final night of Grudgefest was held at Sacramento Raceway in Sacramento, California.  Grudgefest is an event where people can drag race their cars at the track, but instead of the normal ‘race yourself’ drag race where you’re fighting to get the best time, you can also line up against [...]]]></description>
		<link>http://articles.sromagazine.com/grudgefest-at-sacramento-raceway/</link>
			</item>
	<item>
		<title>Do body kits bolt right on?</title>
		<description><![CDATA[Body kits are certainly designed to be bolted on to  your vehicle.  That being said, most body kits are hand-made  products.  The original designs were done by hand, the molds were made by  hand, and the parts themselves are made by hand.  So you will not have the  same installation experience [...]]]></description>
		<link>http://articles.sromagazine.com/do-body-kits-bolt-right-on/</link>
			</item>
	<item>
		<title>What color do body kits come in?</title>
		<description><![CDATA[Every brand comes in a different color.  But all body kits come unpainted either way, meaning you have to get them painted after your receive it. Most body kits come in either a white, black, or grey gelcoat though, depending on the brand.  Vision Autodynamics for example makes all their body kits with [...]]]></description>
		<link>http://articles.sromagazine.com/what-color-do-body-kits-come-in/</link>
			</item>
	<item>
		<title>Do I have to use hood pins if I buy a carbon fiber hood?  Is it a huge risk not using them?</title>
		<description><![CDATA[We wouldn&#8217;t say it&#8217;s a huge risk, and many people do not use them.  It&#8217;s just an extra precaution to avoid a disaster on the road.  The latch on the hood interfaces with your factory latch receiver, but it&#8217;s not made by the car manufacturer so it&#8217;s not necessarily an OE latch.  [...]]]></description>
		<link>http://articles.sromagazine.com/do-i-have-to-use-hood-pins-if-i-buy-a-carbon-fiber-hood-is-it-a-huge-risk-not-using-them/</link>
			</item>
	<item>
		<title>V8 Ricers Sacrilege or Genius?</title>
		<description><![CDATA[You’re driving down the street when you hear it, a loud and rugged roar of an engine, and then you see it in your rearview, a beautiful pearlescent orange Mazda RX-7 pulling up next to you in the stoplight. You try to guess what he is running under the hood but you just can’t recognize [...]]]></description>
		<link>http://articles.sromagazine.com/v8-ricers-sacrilege-or-genius/</link>
			</item>
	<item>
		<title>1993-1997 Ford Ranger Billet Grill Installation</title>
		<description><![CDATA[
First, pop the hood, and prop it up.

There are six screws holding the top of your factory grill securing it to the frame. Remove them. Then, slide the grill outwards away from your Ranger.

This is what your factory grill will look like. You will have to use a hacksaw to remove the top panel( you [...]]]></description>
		<link>http://articles.sromagazine.com/1993-1997-ford-ranger-billet-grill-installation/</link>
			</item>
</channel>
</rss>
